[email protected]© 2013 ikan Corporation. All right reservedMS2121.5" 3G-SDI Studio Monitor USER GUIDE
Waveform IntensityAdjust waveform intensity.Waveform & Vector SizeAdjust size of Waveform & Vector.Waveform & Vector BlendAdjust transpare
DISPLAY 2Exposure Range Check (Video Range Check)Checks Y, C level and displays over-exposed or under-exposed area on screen. The base value can be Y,
Focus Assist ColorSet brush color of focus assist mode among Blue, Green, and Red.12
COLORColor TemperatureSelect color temperature among 3200K, 5400K, 6500K, 9300K or USER. (Gain and Offset menu are displayed on USER temperature only)
MARKERMarker RatioSelect one of preset markers or user marker. To display marker, press Marker button in front of the monitor.Center MarkerSet prefere
User Marker H1 / User Marker H2 / User Marker V1 / User Marker V2Set user marker’s position. H1 for left, H2 for right, V1 for top, V2 for bottom. The
OSDTimecode Display On/OffTimecode PositionSet the position of timecode.OSD Display TimeSet menu display time (seconds)MENU PositionSet menu position
Service 1: general captions.Service 2: translated captions.Service 3,4: not assigned.CC608 StartLineDisplay line of captions are selectable by user. (
AUDIOEmbedded Audio LeftSelect audio channel for left (Ch 1 ~ 15)Embedded Audio RightSelect audio channel for right (Ch 2 ~ 16)Audio Level MeterTurns
GPIGPI ControlTurns on/off external monitor control function.GPI Port 1,2,3,4,5,6Assigns each GPI port’s function. (e.g. SDI 1 input, HDMI input, Tall
ContentsSafety Instructions...3Front...
SYSTEMFunction 1,2,3,4Assigns a function to each function button. See FRONT section for detail.BacklightSet the backlight intensity from 0 to 40. An L
Firmware VersionThis version number is required when you request for service.Operating TimeThis indicates total hours that the monitor operated.21
External Remote ControlConnecting GPI Port(RJ-45)Update Port (RJ-11)123456Update (RJ-11)Update Terminal Assignment1 PIN NC 4 PIN GND2 PIN RX+ 5 PIN TX
Assignable functions are listed below. Function Name Description SDI-1 InputSwitches the input to SDI-1 SDI-2 InputSwitches the input to SDI-2 HDMI
List of Compatible Video Formats (HDMI/Composite)NOSignal InputFormatsINPUTCompositeSD-RGBHD-YPbPrHDMI1 NTSC O O2 PAL O O3 720*576/50i X O4 720*480/59
List of Compatible Video Formats (SDI)NOInput Signal FormatsComposite/ S-VideoComponentSDIDVIYPbPr RGB1 NTSC√- - --2 PAL√- - --3 525/60i (SD)-√
SpecificationsBSM-182 i BSM-212 i BSM-242 i Input2 x BNC HD/SD-SDI, 1.485G/270M3 x BNC Analog(YPbPr/CVBS/S-Video/RGB)1 x HDMI HDMI (with HDCP v.1.1),
DimensionsBSM-182i (WxHxD)438.4 x 310.8 x 66.4mm(17.2 x 12.2 x 2.6 inches)BSM-212i (WxHxD)505.6 x348.0 x 59.2mm(19.9 x 13.7 x 2.3 inches)BSM-242i (WxH
www.ikancorp.comCONDITIONS OF WARRANTY SERVICE • Free service for one year from the day of purchase if the problem is caused by manufacturing error
Safety Instructions• To help avoid damaging your monitor, connect only one power (AC or DC) in operation.• Rough handling of product may cause physica
FrontStandby (Power)Input Switcher (SDI 1, SDI 2, HDMI/DVI)AnalogSwitch analog input in the order of CVBS1 -> CVBS2 -> CVBS3 -> SVIDEO ->
MenuEnterKnob for Adjustment or EnterKnob used to adjust Brightness / Contrast / Chroma / Phase or Enter button.Headphone Jack5
RearAC InputPlease check Power Cord, Power Voltage, Supply power for power input are suitable for the standard before use.Please do not mix AC power a
USB PortUSB Firmware Update Port.MENU DescriptionGeneral Cautions for OSD menu or DisplayThe menu may not be displayed even when user pressed Menu but
VIDEOBrightness, Contrast, Chroma, Phase, SharpnessAdjust color representation values.SDI SwitchingNormal : Use Normal in general condition but the sc
DISPLAY 1AspectSet the aspect ratio of the screen. 16:9, 4:3, Native(Original) are selectable. This selection is ignored on 1080i, 1080p, 720p.1:1 Sca
Comments to this Manuals